FI-VOF16XXX SERIES
OVERVIEW
FI-VOF series fiber optic video/data/audio transceiver supports any high resolution dynamic or stationary picture high-fidelity transmit. It also can be anti-disturbance against several signals, environment, and work stably. It is widely used in security monitoring and control, high way, electronical policy management, automation control, intelligent residential districts and so on.
It can work shortly after it is installed. You could select any date interface by set. It is connected easily and it can indicate power supply, link, video, also adjust video. There are two way installation kits available: stand-alone and rack mounted.
It can be used in varios ways, for example:
- Intelligent transportation system;
- High speed way video monitoring and control system;
- Toll monitoring and control system;
- Close circuit TV industry monitoring and control;
- TV program switching channel transmit;
- High-fidelity video conference system;
- Security monitoring and control system.
FEATURES
- Completely digital fiber transmit platform;
- No need to configuration or any adjusting during the instalation, user friendly design;
- Based on self copyright IC;
- No interference between analog in adjusting channel, picture and range;
- Four steps filtering;
- Completely digital, broadcast transmition efficiently managed by specific IC;
- High speed 10/100M Ethernet channel;
- Full speed asynchronous date channel;
- Flexible configuration on the same platform;
- Power supply, link, video by dynamic indication;
- Self-adapt in PAL, NTSC, SECAM standards;
- ASIC based design;
- Transmit distance: up to 80KM;
- Power supply: 220v,-48v,+24, +12v,+5 (optional), any specific on requqest;
- Two installation types: stand-alone wall method or rack mounted in 19 inches 2U chassis;
- Special MINI type design for limited space enclosures!
SPECIFICATIONS
Video interface:
- Number of Video Input: 16 Channels
- Input/output impedance: BNC 75 ohm unbalance interface;
- Input/output voltage: peak 1 vpp, max 1.5 Vpp;
- Signal: PAL/NTSC/SECAM;
- Video bandwidth: 8MHZ;
- Video number wide: 8 bit;
- Differential gain: <1%
- Differential phase: <0.6°
- Slope: <0.5%;
- Luminance delay inequality: 10ns;
- Luminance gain gap: ±10%;
- Weighted noise ratio: 67db;
Date interface (can support 1~4 line asynchronous date RS-232/485/422)
- Physical interface: industry standard terminal lead;
- Full duplex/half duplex;
- Interface type: RS-232/485/422 Manchester;
- RS232 rate 0-115.2Kbps;
- RS-422/485 rate: 0-115.2Kbps;
- RS-422/485 transmit distance: 0-1200m
- RS-422/485 agreement support RS-485/422 agreement
- Error rate: <10-9
- Fiber interface
- Physical interface: FC or ST or SC
- Fiber type: single/multi mode
- Transmit distance: multi mode up to 2 km, single mode 20/40/60 km, WDM available
Audio interface: supports mono or stereo audio
- Audio input/output: impedance 600 balance/unbalance interface industry standard terminal lead.
- Audio input/output level: 2Vp-p
- Frequency response: 10 Hz-20 KHz
- Audio channel width: 24 bit
- Weighted noise ratio: 95db
- Total Harmonic Distortion: 0.1%
Ethernet interface
- Physical interface: shielding RJ-45
- Support IEEE 802.3/802.3u/802.1q VLAN
- IEEE 802.3x full duplex and Back-Pressure half duplex flow control.
Working environment
- Work temperature: -30~+75
- Storage temperature -45~+85
- Humidity : 0-95% without condensation
- Input voltage :220V-48V,+24V+12,+5V optional
- Power 5W (single terminal)
- Size of products : 483 x 220 x 44 mm.
ORDERING INFORMATION
Model name format: FI-VOF(1)(2)(3)(4)(5)(6)(7)-T/R(8)
Explanation:
FI = Brand name (FI-LINK Company)
VOF = Video Over Fiber
(1) = the number of Video channels (‘0’ means not support)
(2) = the number of Data channels (‘0’ means not support)
(3) = the number of Audio channels (‘0’ means not support)
(4) = the number of Ethernet channels (‘0’ means not support)
(5) = the number of Contact closure channels (Blank means not support)
(6) = Fiber cable type (‘S’ = Single mode; ‘M’ = Multi mode)
(7) = Fiber transmission distance (Km)
T/R = Tramsmitter / Receiver (1 pair)
(8) = Simplex Connector type (‘S’ = SC; ‘F’ = FC; ‘T’ = ST; ‘L’ = LC)
APPLICATION DIAGRAM
